Free Vacumobil sizing calculator
Which Vacumobil mobile dust collector fits your shop?
Build your machine list and get the right Vacumobil, its airflow, main duct size and yearly energy cost. It sizes by the machines you run, not by square footage.
Updated November 2026 by Höcker North America.
Size your Vacumobil
Build your machine list and get the model, airflow, duct size and yearly energy cost. Your result updates as you go. No email needed to see it.
Tap a common machine or pick from the full list. Each one starts at its typical CFM. Change the port to match yours, or type the manufacturer's CFM.
Machines you checked as “All shift” are always counted on top of this.
Estimates only. Duct layout, run lengths, static pressure and local code are checked when you request the configuration sheet. See how it sizes.
- With 15% margin
- 0CFM
- Running at once
- 0CFM
- Unit rated / max
- n/a
- Main duct
- 0IN
- Motor
- n/a
- Energy per year
- n/a
- Installation
- n/a
- Gate control
- n/a
Why this unit, what's included
Email me the configuration sheet: every machine, the recommended Vacumobil and a free review of duct runs, static pressure, waste handling and NFPA 660.
Quick answer
How do I size a Vacumobil? Add the airflow of machines that run all shift, then the largest machines your operators run at the same time, and add 15% margin. Pick the smallest Vacumobil rated for that airflow. Above 5,000 CFM, we recommend a second Vacumobil or, ideally, a central system. A unit handling more than 5,000 CFM, or one that serves a wide belt sander, goes outside.
What you get, free
Your configuration sheet is ready to quote from
Model and configuration
Recommended Vacumobil, filter cleaning and waste discharge.
Included and recommended options
Fire suppression, gate valve control and everything that comes standard.
Indoor or outdoor
Where your unit can sit, based on airflow per unit.
Review by our team
Checked against your duct layout, waste handling and NFPA 660.
How the sizing works
One mobile unit, sized to the machines you run
Count what actually runs at once
Continuous machines like CNC routers and wide belt sanders always count. For the rest, count only as many machines as you have operators running them at once. Automatic blast gates close idle ports, so the Vacumobil pulls air only where work is happening.
Vacumobil models on U.S. 460 V / 60 Hz
Rated airflow at 20 m/s inlet velocity.
| Model | Rated CFM | Max CFM | Inlet | Bins |
|---|---|---|---|---|
| Vacumobil 250 | 2,080 | 3,650 | 10 in | 3 |
| Vacumobil 300 | 3,000 | 4,120 | 12 in | 4 |
| Vacumobil 350 | 4,080 | 5,885 | 14 in | 4 |
| Vacumobil 355 | 4,195 | 5,885 | 14 in | 4 |
Show the math and assumptions+
Design CFM = continuous machines + the largest machines your operators run at once. System CFM = design × 1.15. Each machine starts at its typical airflow; change its port and the calculator uses the airflow that port needs at 4,500 feet per minute (about 395 CFM for a 4 in port, 885 CFM for a 6 in port).
The calculator picks the smallest Vacumobil whose rated airflow covers system CFM, then checks maximum airflow. If one unit can't carry the load, it splits it across two or more. Any unit above 5,000 CFM must be installed outside. In the top size it recommends the 355, built for 460 V / 60 Hz; the 350 is shown as the alternative.
Energy per year = motor kW × hours a day × days a year × your power rate.
Run more numbers
Questions
Vacumobil sizing FAQ
How much airflow does a Vacumobil move?
+
Rated airflow runs from about 2,080 CFM on the Vacumobil 250 to about 4,195 CFM on the Vacumobil 355, measured at 20 m/s inlet velocity. On U.S. 460 V, 60 Hz power, maximum airflow runs from about 3,650 CFM on the 250 to 5,885 CFM on the 350 and 355.
Do I size for every machine in the shop?
+
No. Continuous machines like CNC routers and wide belt sanders always count. For the rest, count only as many machines as you have operators running them at once.
Can a Vacumobil sit inside the shop?
+
Often, yes. Every Vacumobil has integrated fire suppression and a blow back damper, and returns air with residual dust under 0.1 mg/m³. A unit handling more than 5,000 CFM must sit outside, and wide belt sanders are typically not in compliance on an indoor unit. Every Vacumobil can be installed outside.
What happens to the dust and chips?
+
Three choices: collection bins you roll out and empty, a briquetting press, or a rotary valve that sends waste to a silo, dumpster, or big bag.
When is a mobile dust collector the wrong choice?
+
When the machines running at the same time need more than 5,000 CFM, or when the machines are spread across a large building. That usually calls for two Vacumobils or a central MultiStar system.
Who sells and supports the Vacumobil in the United States?
+
Höcker North America sizes, configures, and supports every installation. Call 616.881.6698.
Sources: Höcker Polytechnik Vacumobil brochure, February 2026; NFPA 660. The calculator sizes airflow only. It is not an NFPA 660 compliance review.